Temperature Controllers

Регуляторы температуры


Our Temperature Controllers are designed to work with different heating elements and a variety of optional accessories including a simple Heater Assemblies, Dry Bath, BLM Cell Holder and Extruder Warmer.  Two modifications are available.  TC-02A can be connected to high power AC heaters (lamps, heater fans, water immersed heaters etc.) for large volume heating, or to compact heater assemblies for temperature control of fluorometer cells, or microscope stages.  TC-12 version is similar but smaller and have lower power, no AC and no recorder output. Each unit comes with one temperature sensors attached to 3 feet (90 cm) cables.  Second sensor assembly (Part # AD592) is optonal and need to be purchased separately.


 Наши регуляторы температуры сконструированы для работы с различными нагревательными элементами и разнообразным дополнительным оборудованием включая простые Нагревательные элементы, Сухую ванну, Держатель БЛМ ячейки и Подогреватель экструдера липосом.  Производятся в  двух модификациях. TC-02A можно использовать для нагрева сравнительно больших объёмов с сетевыми нагревательными элементами большой мощности (светильники, вентиляторы подогрева, водопогруженные нагреватели и т.д.), так же как и для компактных низковольтных нагревателей для контроля температуры ячеек флуорометра, или столиков микроскопа.  Версия TC-12 это компактный вариант с теми же параметрами, но без созможности подключения сетевых нагрузок и самописца. Каждый блок укомплектован датчиком температуры на кабеле длинной примерно 90 cм. Дополнительный датчик (AD592) в комплект поставки не входит и если он необходим, то его нужно заказать отдельно.

 

SPECIFICATIONS
TC-12 TC-02A
Temperature setting range, oC  Диапазон установки температуры 20-80 20-80
Temperature measurements range, oC  -10 to +100  -10 to +100
Resolution,  oC 0.1 0.1
Accuracy, oC +/-1 +/-1
Recorder output No BNC, 1 mV/oC
Number of sensor inputs 2 2
Sensor dimensions LxD (mm) 4x5 4x5
Controller dimensions, HxWxL (sm.) 9x16x12 (3.5"x6"x5") 9x21x15  (3.5"x8"x6")
Output power 
(2.1/5.5 mm DC connector;  standard AC socket)		 12W, 24V DC  24W, 24V DC ; 
300W, 120V AC

Heater assemblies 

           

            HA series heater assemblies are simply power resistors with ceramic or TO type body attached to 4 feet (120 cm) cable with 2.1/5.5 mm connector that match TC-12/TC-02A output.  Heated surfaces are electrically non conductive and can be mounted directly to metal surfaces using enclosed hardware.  Ceramic heaters can be used at maximum power without heat sink (but with sufficient air cooling) and good for temperatures up to +150oC.  TO-XXX heating elements are compact and easy to mount with a single screw but need a good contact with metal heat sink (use of silicone heat sink compound is recommended).  They can be irreversibly heat damaged if used unmounted.  It is not recommended to use them for heating to temperatures above +80oC.

 


         HB series heaters are designed for easy mounting on our or other aluminum bench plates in order to provide stable, elevated temperature to different experimental rigs assembled on those plates.  We tested both with FC-30A (aluminum) Faraday cage and found that HB-12 is capable to rise temperature by about 10 oC, while for HB-25 temperature increase was 15 oC.   

         HB-12 has 6-32 threaded hole in the base and mounts with a single screw.  HB-25 is larger and require two mounting screws.  It has a pattern of six 6-32 threaded holes that fit square pattern of  holes in most standard bench plates: 1", 25 mm and 30 mm.  Both heaters have 5 mm diameter, 15 mm deep hole for temperature sensor and 4 feet (120 cm) cable with 2.1/5.5 mm connector.  

 

 

 

Specifications:

Part #
Peak power with 
TC-12 or TC-02A
(Watt)
Max mean power (Watt)
Resistance (Ohm)
Body Size (mm)
Construction
HA-5
6
5
100
 10x10x23
Ceramic
HA-15M
6
15
100
8x11x3
TO-126
HA-10
12
10
50
 10x10x50
Ceramic
HA-30M
12
30
50
10x16x3
TO-220
HA-20
23
20
25
 10x10x50
Twin Ceramic
HA-60M
23
60
25
10x16x3
Twin TO-220
HB-12
12
 12
50
 80x45x15  9 mm Alum. base
HB-25
22
 25
26
 120x50x15 9 mm Alum. base

 

 


Dry Bath
This compact unit is designed to work with  TC-02A or other temperature controllers that have 12-24 V output.  Allow keeping small number of microcentrifuge tubes (0.5-2 ml size) above room temperature near your workspace.  Two ceramic heating elements attached to the bottom of massive aluminum alloy heating block provide even heat distribution to up to 15-16 vials.  (One-two well should be reserved for feedback temperature sensor and thermometer).
Part # DB-1

 

Specifications:
Max. Temperature     110 oC
Max. Power              25 Watt
Heater resistance       25 Ohm
Dimensions               90x125x50 mm (3.5"x5"x2")

 

Back to the top of the page
 Go To Prices
HOME
11-27-19  R_TC.html